Engine Installation Day: Mates, Hoists, and the Art of the 20-Degree Tilt

The install day

Sunday was the big day: engine install day.

It almost didn’t happen at all. Right up to the wire, I was waiting on a delivery of the Schnorr washers for the engine mount bolts that were either missing from my kit or buried somewhere I couldn't find. Luckily, they arrived just in time. I had also managed to track down a 3/8" hex bit socket for the engine mount bolts—more on that particular tool later.

In the end, four mates came round to lend a hand: Chris, Ronan, John, and Richard. That made five of us in total. Five people standing around a Caterham engine bay is definitely overkill, but as it turned out, having plenty of steady hands to guide things into place was invaluable. The funniest moment of the day was watching three grown men huddled over the bay simultaneously arguing about which hex bolt went where and what torque setting to use. A classic case of too many cooks, but we sorted it out in the end!

The Hoist and Gravel Logistics

I had managed to borrow an engine hoist from a friend whose mum had kept one sitting in her garage for years—an absolute lifesaver.

My garage sits at the end of a gravel driveway, which was a worry. Trying to drag small engine crane castors across loose gravel with an engine swinging on the hook is a recipe for disaster. To get around it, I laid down sheets of thick plywood over the gravel leading right into the garage. It worked brilliantly, giving us a smooth, flat rolling track for the hoist.

We rigged up the engine on the load leveler, used a digital angle gauge to get it hanging at roughly a 20-degree tail-down angle, and started wheeling it towards the car.

Boom Geometry: A Lesson Learned

We dropped the hoist down slightly to clear the front rails and got about halfway into the install when we hit our first snag: the upright mast of the engine crane was hard up against the front of the chassis, and the engine wasn't nearly far enough back.

The hoist boom is extendable, but you can’t safely pull the pin and extend the boom while it's holding an engine. We had no choice but to back the whole thing out, lower the engine carefully onto timber blocks on the floor, extend the arm out to the next setting, get it balanced back to 20 degrees, and start again.

Needed to adjust the boom length, height and employ some ply for the gravel


Into the Transmission Tunnel

Once we went back in with the extended reach, things went much smoother. The key really is taking your time.

  • The Angle: We kept the assembly tilted tail-down at about 20 degrees to feed the gearbox into the mouth of the transmission tunnel.

  • The Chassis Snag: There’s a lower protrusion on the gearbox casing that has to hook cleanly over the chassis crossmember. If you drop the engine too low too early, it catches on the chassis and simply won't slide backwards.

  • The Trolley Jack Trick: As the gearbox moved further into the tunnel, we slipped a trolley jack underneath it from below. That allowed us to lift the tail of the gearbox up and pivot the engine back towards level as we pushed it home.



Engine Mounts & The Socket Trap

Getting the engine settled onto its rubber chassis mounts threw up two tricky moments:

1. Dirty Threads in the Rubber Mounts

When we tried to thread the mount bolts into the chassis rubber bobbins, one side refused to bite finger-tight. If you cross-thread or seize a bolt inside one of those bonded mounts, you're in big trouble. We took the mount off the chassis entirely to inspect it on the bench and found the internal threads full of grit and crud. I carefully ran a bolt through with a spanner to clean out the threads, which freed it right up. It threaded in smoothly by hand after that.

2. The 3/8" Hex Bit Headache

The engine mount bracket design means the cap head bolt sits down inside a recessed tube. I had bought a standalone 3/8" hex bit socket online for the job—paying nearly £13 with shipping.

The annoying thing? The hex bit itself isn't long enough. The wider 1/2" drive collar of the socket fouls on the top of the bracket tube before the hex tip can seat fully down into the bolt head. I’ve managed to get it nipped up partially, but there’s no way to get a torque wrench on it without stripping the head. I'll need to track down an extra-long 3/8" hex bit before I can torque it to spec

<Insert Photo of bolt>

Gearbox Mounts & Tunnel Clearances

The gearbox mounting crossmember went in fine, though I did give Lee at Caterham a ring to double-check something first.

To fit the bolts, you genuinely have to punch them straight through the foil-faced heat-shield insulation on the transmission tunnel. It feels completely wrong—like you're ripping up brand-new trim—but once the bolt pushes through and tightens down, the washer clamps the insulation neatly into place.

One of the bolts needs to punch the insulation. The other ties into the chassis


Once bolted up, the engine sits at a noticeably odd tilt, leaning towards the passenger side and sitting remarkably close to the transmission tunnel wall. From what other builders have documented, that’s just how they sit. There's no adjustment in the mounts anyway: once the bolts are in, that is where it lives.

Tight fit


Front Hose Shortcut (And That Spring Clip)

The assembly manual suggests stripping off a good chunk of the front pipework around the intercooler/turbo housing before dropping the engine in. In reality, you don't need to dismantle the whole lot.

We simply unhooked one front hose, dropped the engine past the top chassis rail, and routed the hose around the rail before reconnecting it.

Ironically, the single hardest physical job of the entire day was wrestling the heavy-duty spring band clamp back onto that hose in the tight gap at the front. It was an absolute pain in the backside to compress and seat properly, but it saved tearing the whole front intake assembly apart.

Interesting geometry - just needed to unclip and thread round the strut


What’s Next?

Despite the odd hiccup, getting the engine and gearbox sitting on their mounts feels like a massive step forward.

Looking at the engine bay now, there’s a whole lot of wiring loom to sort out. Even though the manual suggests otherwise, my plan is to tackle the electrics first—connecting the engine harness to the chassis loom and securing the wiring runs neatly out of the way before the space gets choked up with coolant hoses and plumbing.

This week: wiring, engine plumbing, and maybe even a start on the rear transmission.

The install in 40 seconds


An overview post install






Comments