Fitting the front upper and lower wishbones is essentially the first major mechanical assembly task in the Caterham build manual. If you read any builder blogs beforehand, you will know that getting the lower wishbones into their chassis mountings is notoriously difficult due to the tight clearances and washer stacks.
![]() |
| These are the buggers - the last one is a fight.... |
It proved to be exactly that—and then escalated into my first major cock up of the build.
Squeezing the Lower Wishbone Washers (The "V" Technique)
The manual specifies a 2-2 washer configuration on the lower wishbone pivots to set the front suspension caster:
Two washers between the rear chassis mount and the wishbone bush.
Two washers between the wishbone bush and the rear retaining mount.
These are large, chamfered plain washers, and the chamfered side must always face inward toward the wishbone bush.
While the first three washers slip in relatively easily, there is virtually zero clearance left for the fourth washer. After struggling with it, I worked out an effective method:
Draw the third washer slightly back out of the gap.
Angle the fourth washer against it to form a slight "V" shape at the opening.
Gently and progressively tap the pair into alignment using a nylon mallet (and occasionally easing them with a flat screwdriver blade where access was restricted).
Then a lot of wiggling to try to get them to line up with the hole / bolts
Having perfected this technique, I soon found out I would have to do the entire job all over again.
The Handing Confusion: Upper Wishbones
Once the wishbones were bolted up, I discovered I had installed them on the wrong sides of the car.
The Caterham assembly guide parts list refers to the upper wishbones as:
Upper Wishbones (LH / RH)
I took this to mean the kit supplied one for the left-hand side and one for the right-hand side of the car, rather than indicating that the components themselves were handed with asymmetrical geometry. The labels on the packaging bags did denote LH and RH, but once unpacked and laid out on the bench, telling them apart is far from obvious. The manual illustrations are quite basic and do not clearly illustrate the subtle angle offset on the outboard ball joint mountings.
| Upside down (but I didn't know it at this point) |
So unluckily I ended up with the upper wishbones bolted to the chassis on the wrong sides.
Fitting the Front Dampers and Chassis Deflection
Before realising the wishbones were reversed, I had moved on to installing the front spring/damper units.
Fitting the lower damper eye into the wishbone is straightforward, but the upper mounting bolt is heavily restricted by the chassis side skin:
The chassis side panel prevents the top cap-head bolt from sliding straight into the mounting aperture.
As documented by other builders, the solution is to firmly press the aluminium chassis skin inward with your thumb to create just enough clearance for the bolt to drop into the sleeve. The skin is thin enough to flex without permanent deformation.
Because the space inside the top bracket is so restricted, you cannot get a conventional socket or torque wrench squarely onto the bolt head. A cut-down 6mm hex bit used in a ratcheting ring spanner is the only reliable way to tighten it.
Outboard Alignment and the Bent Lower Ball Joint Pin
With the dampers hung, I attempted to mount the front upright assemblies to the upper and lower wishbones.
This is where everything came to a halt. With the car raised on stands, the suspension was hanging at full droop under its own weight while the dampers were fully extended. Even with correctly oriented wishbones, aligning the upright tapers requires supporting and raising the lower wishbone with a trolley jack.
Because my wishbones were reversed, the geometry was fighting itself. Unaware of the root cause, I tried easing and jacking the assembly into position to get the lower pin through the spherical bearing and top-hat spacer. The components bound hard.
When I took the assembly back apart to see why it would not seat, I found that the threaded pin on the bottom of the upright assembly was badly bent. It takes considerable force to bend a high-tensile suspension pin like that, and while I questioned how much load the jack had actually applied, the damage was done.
![]() |
| Did I really bend it that much ! |
I took the damaged assembly down to Dan at HWM Caterham. He was skeptical that the reversed wishbones had placed the upright into such severe misalignment under compression, but Caterham were not willing to entertain that it could have been damaged before. I guess fair enough, but I;m still not 100% sure. Dan, fortunately, had the replacement lower mounting component on the shelf. Replacing it requires a specific press tool, so I had Dan swap the component over directly. It was an avoidable mistake that cost me a couple hundred pounds and delivered a sharp blow to my confidence, but it was an essential lesson in never forcing suspension components when alignment does not feel natural.
By the way, see my post on getting some help from this from the Caterham forum. Aside from the issue I’d casued, it reveals how diffucult it can be to remove the brake assembly normally. There’s a V-shaped fitting that gets wedged (by design), and can be impossible to prise open.
The Bush-Torquing Dilemma
With the correct wishbone orientation restored and the rebuilt uprights fitted, I ran into the standard conundrum regarding torque settings:
The Rule: Builder advice and general chassis practice dictate that wishbone pivot bolts through bonded rubber bushes should only be fully torqued once the car is resting on its wheels at final ride height. Torquing them at full droop locks the bushes with permanent torsional twist once the car is on the ground.
The Snag: Once the damper is bolted into place, access to the rear upper wishbone mounting bolt is almost completely blocked.
I checked this with Lee at Caterham. His guidance is that the rear upper wishbone pivot bolt must be torqued to spec prior to installing the damper, while leaving the remaining front and lower pivot fixings finger-tight until the car is on the ground. So why could the manual not say that. It explictilty says NOT to torque any. Grrrr…. Off with the damper again !!!
![]() |
| Hopefully this is all now correct - lets see on PBC |
Steering and Front Anti-Roll Bar (ARB)
With the wishbones and uprights finally installed correctly, the track rod ends mated to the steering arms without fuss. However, I note that the wheel fittings look like they are not particuarly parallel, and not necessarily exactly vertical. I can see that this could be adjusted by the number of turns on the steering column ends. I checked with various blogs etc., and there is certainly no consensus as to how many exposed threads should be showing. My understanding is that this will affect the tracking. I then realised that in order to change this, you’d need to break the brake fitting that gets wedged (see above), and Dan said he’d be checking this in the PBC. So after all the hassle, frustration and disappointment with myself, I’ve decided to leave it like that and ensure Dan does check it !
I then moved onto the front Anti-Roll Bar (ARB).
Fitting the ARB went smoothly with one essential modification:
Bush Preparation: The rubber "cotton reel" bushes were lubricated with rubber grease and seated into their chassis brackets, then slid onto the bar.
Dremel Modification: The green plastic mounting balls thread onto the ends of the ARB (secured with Loctite on the bar threads). When test-fitting them into the cups on the upper wishbones, the fit was impossibly tight due to excess black powder coating inside the sockets. I used a Dremel with a small sanding drum to gently buzz the powder coat out of both wishbone cups back to bare metal.
Seating the Bar: Once cleaned up, the balls were packed liberally with multi-purpose bearing grease. One ball was seated into its wishbone cup, and the opposite end was flexed into position by hand.
Securing: The mounting brackets were aligned with the front chassis tubes and torqued to 20 Nm, and the rubber dust boots were zipped down over the cups with small cable ties.
![]() |
| Slide on before but dont fix till last |
The front corner assemblies are now correctly handed, bolted up, and ready for final brake plumbing and steering alignment.




Comments
Post a Comment