Engine Bay Progress: Plumbing, Electrics, and the Usual Manual Quirk

With the engine in the chassis, I spent a solid day working through the engine bay plumbing and sorting out the electrical connections. You get a big box of strangely shaped hoses and a batch of wiring connections, and it is simply a matter of working through them slowly to figure out where everything goes.

All plumbed in


1. Coolant Pipe Extension

The main issue I ran into—and where the Caterham Assembly Guide (CAG) really falls short—was with the radiator piping.

One section of the radiator pipe looks far too short to reach its destination. It turns out you have to use a cut section of the supplied fuel hose as an extension piece to bridge the run, even though "fuel hose" is printed right on the rubber. Once you know that, it connects up without issue, but the manual makes it far harder than it needs to be.



2. Turbo Boost Solenoid and Intercooler

Working out the electrical connections and vacuum lines around the turbo required some head-scratching:

  • Turbo Solenoid Piping: The manual says you have to fit the vacuum lines to the solenoid, but on my engine spec, those lines were already fitted from the factory.

  • The Intercooler: Not knowing much about engine internals before this build, I initially wondered if the wiring or piping went to the intercooler. I now realise the intercooler is completely passive and has no electrical connections whatsoever.

  • Solenoid Plug: I couldn't spot the electrical connector for the turbo boost solenoid initially—the plug just didn't look like what I expected, and I hadn't looked closely enough. A quick check with Caterham and Lee pointed me in the right direction.

  • Plemum release hose: Not sure if tthats the right name, but there was a random thin rubber pipe coming from the turbo (pre fitted) and another one poking up from the plemum with an organge value. The manual does not mention them at all - it turns out they need to be connected !

Once those were identified, fitting the rest of the pipework was straightforward and actually good fun, like solving a large jigsaw puzzle.

Need to attached the 'upward pipe' to the turbo 'random pipe'

All these grey pipes were pre fitted, depsite the manual saying to fit them. Note the solenoid connectors - there are 2 of them hidden away


3. Clutch Cable and Purge Valve

Fitting the clutch cable went smoothly with no real drama.

Routing the pipework threw up one oddity on the driver's side of the engine:

  • There was an extra pre-formed rubber pipe attached to the engine block.

  • You can connect this pre-formed pipe to the fuel vapour purge valve, but doing so would require an extra inline connector.

  • Instead, I routed a clean run of hose directly between the purge valve and the plenum chamber. It creates a smooth, tidy curve into the valve without the extra join, which looks much cleaner.

The randomly attached pre formed tube could be used to help connect the purge pipe to the plenum. Nothing in the manual. I'd already routed it direct which apparently is ok


4. Loom Routing and Pending Jobs

I tried rerouting the engine wiring harness two or three times to find the cleanest path through the bay, and the current layout looks neat. However, final tie-wrapping and securing are on hold for two items:

  1. Battery Connections: Lee confirmed that I need a specific set of battery terminal covers and connectors. I can't find them in my kit packs, so I am waiting for Caterham to send those out before finalising the battery area and tidying up the excess cable.

  2. Lambda / Oxygen Sensor: I can't finish routing and securing the exhaust branch of the harness until the exhaust system is actually fitted to the car. I won't know how much slack is needed for the oxygen ($O_2$) sensor lead until the collector pipe is in place.

Summary

Overall, it was a very satisfying day on the build. Working through the engine bay systematically means I finally understand what every hose and connector actually does—even if identifying problems down the road will still be a learning curve! The next step is getting the exhaust hung and finishing off the remaining wiring terminations.



Comments